I have completed all this steps and able to connect via wifi. But LAN is not working. When i Checked LAN settings in advanced setup, it enables DHCP automatically. Kindly help. Thanks in advance.smshashi said:Follow these steps in this order for D-Link 2730 modem, for setting up both as a LAN router and Wifi Access Point. Connect the LAN cable to LAN1 port on router and login to router ip (192.168.1.1) for doing these setup. Login with admin/admin as userid/password.1) Advanced Setup-> Layer2, Add atm0 with default settings2) WAN Service -> Add with Bridge type selected, keep others default3) Wireless ->Enable Wireless, and give your own SSID, keep others default4) Wireless-> Security-> Give Network Authentication as WPA-Personal, and passprase will be your own password to connect to WiFi5) Interface Grouping -> Give a group name as WAN, and select WL0, LAN2, LAN3, LAN4 from right to left, Apply/Save. Now there should be 2 groups one Default with LAN1 and other with new Group Name6) LAN -> In the right top dropdown select WAN group and disable DHCP, Apply/Save7) Management->Settings->Backup your settings8) Management -> RebootConnect the output from Tikona to LAN2 port on the router, connect your laptop to Wifi on the router using the SSID/passphrase. This should work, else shutdown router for 10 seconds, disable your wireless network and log-off/on again, enable wireless network and try connecting again.After this the ethernet wire coming from Tikona should be connected to LAN2 port, and you can use wifi. Note that LAN1 port is used to connect to the router only (192.168.1.1) after this setup. Go to login page of tikona (1.254.254.254) with ur userid and password given by tikona and login to connect to internet.RegardsShashi
WoW, that's some awesome info, however I tried to get it done on my "ADSL2+CPE Model : AR800V 3.0v" and ended up in vain, as I couldn't find the right settings on the login router page (192.168.1.1), the options to select are totally different, like they are not bsnl modem at all???...Pls provide assistance on the same...smshashi said:Follow these steps in this order for D-Link 2730 modem, for setting up both as a LAN router and Wifi Access Point. Connect the LAN cable to LAN1 port on router and login to router ip (192.168.1.1) for doing these setup. Login with admin/admin as userid/password.1) Advanced Setup-> Layer2, Add atm0 with default settings2) WAN Service -> Add with Bridge type selected, keep others default3) Wireless ->Enable Wireless, and give your own SSID, keep others default4) Wireless-> Security-> Give Network Authentication as WPA-Personal, and passprase will be your own password to connect to WiFi5) Interface Grouping -> Give a group name as WAN, and select WL0, LAN2, LAN3, LAN4 from right to left, Apply/Save. Now there should be 2 groups one Default with LAN1 and other with new Group Name6) LAN -> In the right top dropdown select WAN group and disable DHCP, Apply/Save7) Management->Settings->Backup your settings8) Management -> RebootConnect the output from Tikona to LAN2 port on the router, connect your laptop to Wifi on the router using the SSID/passphrase. This should work, else shutdown router for 10 seconds, disable your wireless network and log-off/on again, enable wireless network and try connecting again.After this the ethernet wire coming from Tikona should be connected to LAN2 port, and you can use wifi. Note that LAN1 port is used to connect to the router only (192.168.1.1) after this setup. Go to login page of tikona (1.254.254.254) with ur userid and password given by tikona and login to connect to internet.RegardsShashi
Hi shashi,smshashi said:Follow these steps in this order for D-Link 2730 modem, for setting up both as a LAN router and Wifi Access Point. Connect the LAN cable to LAN1 port on router and login to router ip (192.168.1.1) for doing these setup. Login with admin/admin as userid/password. 1) Advanced Setup-> Layer2, Add atm0 with default settings 2) WAN Service -> Add with Bridge type selected, keep others default 3) Wireless ->Enable Wireless, and give your own SSID, keep others default 4) Wireless-> Security-> Give Network Authentication as WPA-Personal, and passprase will be your own password to connect to WiFi 5) Interface Grouping -> Give a group name as WAN, and select WL0, LAN2, LAN3, LAN4 from right to left, Apply/Save. Now there should be 2 groups one Default with LAN1 and other with new Group Name 6) LAN -> In the right top dropdown select WAN group and disable DHCP, Apply/Save 7) Management->Settings->Backup your settings 8) Management -> Reboot Connect the output from Tikona to LAN2 port on the router, connect your laptop to Wifi on the router using the SSID/passphrase. This should work, else shutdown router for 10 seconds, disable your wireless network and log-off/on again, enable wireless network and try connecting again. After this the ethernet wire coming from Tikona should be connected to LAN2 port, and you can use wifi. Note that LAN1 port is used to connect to the router only (192.168.1.1) after this setup. Go to login page of tikona (1.254.254.254) with ur userid and password given by tikona and login to connect to internet. Regards Shashi