How to configure tikona with adsl2+ router (Dlink DSL-2750U)

Hi,Recently I bought Dlink DSL-2750U modem+router for home use. I want to configure this router but router WAN port accepts RJ11 cable.And tikona has RJ45 cable.So anybody can suggest solution for this problem?Also this router has USB port for connecting internet dongles.Thanks,Amit Mande

Hi
Please provide the below mentioned information in order to assist you better:

User id:-

OR

Registered Contact Number:-

Email Us: -- TDNservices@tikona.in

Regards
Tikona Services

Hi,

Recently I bought D-Link DSL-2750U modem+router for home use. I want to configure this router but router WAN port accepts RJ11 cable.

And tikona has RJ45 cable.

So anybody can suggest solution for this problem?

Also this router has USB port for connecting internet dongles.

Thanks,
Amit Mande

Hello Mr. Mande,

ADSL routers can only be connected to ADSL connections provided by some Internet Service Providers . The ADSL connectivity is carried over POTS (Plain Old Telephone System) lines that also connects your Telephone(RJ 11 Connector used).

Tikona provides Broadband connecting with Ethernet port and hence WI-Fi connectivity can be provided by a Wi-Fi Router with a Ethernet WAN port (RJ45 Connector Used). Plenty of Wi-Fi routers are available in market . To configure your router , refer to Tikona Broadband Forum • Index page (Path: Board index ‹ Support ‹ Do it Yourself ‹ Configure Wi-fi Router)

Alternatively you can also opt for Secured & maintained @llhome Wi-Fi provided by Tikona at One time charges of Rs 1500 + Taxes.

Thanks & Regards
Tikona Services

Thanks for your reply!My adsl2+ router (DSL-2750U) works with tikona when I connect rj45 of tikona into LAN port of my router. But some times it simple fails.Before this I was having D-Link dir615 router which was working seamlessly for almost one year. From last 1 month I am facing random disconnection. I face same problem when I connect broadband directly to my laptop. It seems that there is some problem from tikona side.Registered no: 9766644004Tikona id: 1104359767At this time I have only one problem that is random loss of connection. Please take a look into it.Thanks!

Thanks for your reply!

My adsl2+ router (DSL-2750U) works with tikona when I connect rj45 of tikona into LAN port of my router. But some times it simple fails.

Before this I was having D-Link dir615 router which was working seamlessly for almost one year. From last 1 month I am facing random disconnection. I face same problem when I connect broadband directly to my laptop. It seems that there is some problem from tikona side.

Registered no: 9766644004
Tikona id: 1104359767

At this time I have only one problem that is random loss of connection. Please take a look into it.

Thanks!

Hi,
We have made a note of your concern. We shall look into it and revert in maximum 48 hours.

Email Us:-- TDNservices@tikona.in

Regards
Tikona Services

Follow these steps in this order for DLINK 2730 modem, for setting up both as a LAN router and Wifi Access Point. Connect the LAN cable to LAN1 port on router and login to router ip (192.168.1.1) for doing these setup. Login with admin/admin as userid/password.1) Advanced Setup-> Layer2, Add atm0 with default settings2) WAN Service -> Add with Bridge type selected, keep others default3) Wireless ->Enable Wireless, and give your own SSID, keep others default4) Wireless-> Security-> Give Network Authentication as WPA-Personal, and passprase will be your own password to connect to WiFi5) Interface Grouping -> Give a group name as WAN, and select WL0, LAN2, LAN3, LAN4 from right to left, Apply/Save. Now there should be 2 groups one Default with LAN1 and other with new Group Name6) LAN -> In the right top dropdown select WAN group and disable DHCP, Apply/Save7) Management->Settings->Backup your settings8) Management -> RebootConnect the output from Tikona to LAN2 port on the router, connect your laptop to Wifi on the router using the SSID/passphrase. This should work, else shutdown router for 10 seconds, disable your wireless network and log-off/on again, enable wireless network and try connecting again.After this the ethernet wire coming from Tikona should be connected to LAN2 port, and you can use wifi. Note that LAN1 port is used to connect to the router only (192.168.1.1) after this setup.RegardsShashi

@smshashi...thanks man. It helped me very much configuring D-Link DSL-2750U. My friend(using BSNL) has bought this product and i checked it with my Tikona connection temporarily.

i recently purchased D-Link 2750u router but im unable to configure to tikona can someone plz provide me step by step instruction

my router stopped responding after trying to complete step 5. I had to then hard reset it. please help. I have a rj45 lan cable coming from my wireless receiver which I need to connect to D-Link 2750u to make my environment wireless.

Hi Shashi,
Thanks for this nice post.
I could configure my DSL-2750u router following these steps.
The next step that I am trying to achieve is as follows:
1. My router has a USB port and I added a HDD onto it.
2. The disk is reachable using 192.168.1.1publicusb1_1
3. After the modifications as described by you, I can access the disk if I connect using LAN1
4. I wish to connect to it using wl0.
5. So I am looking at implementing some routing/NATting
6. But not yet successful.
Can you shed some light on any possible way for this?
Regards,
Kangkan

Hi Shashi,
I have configured D-Link 2750U using your steps. But I cant use more than 2 devices. Can u please suggest a way so that I can login once and all other devices can use wifi as well as via ethernet.
Thanks,
Vimal

Geekays.Net said:

Hi Shashi,
Thanks for this nice post.
I could configure my DSL-2750u router following these steps.
The next step that I am trying to achieve is as follows:
1. My router has a USB port and I added a HDD onto it.
2. The disk is reachable using 192.168.1.1publicusb1_1
3. After the modifications as described by you, I can access the disk if I connect using LAN1
4. I wish to connect to it using wl0.
5. So I am looking at implementing some routing/NATting
6. But not yet successful.
Can you shed some light on any possible way for this?
Regards,
Kangkan

Click to expand...

Sorry, I am not sure about how to configure USB, pls share in the same post with complete steps once ur successful in this.

vvvimal said:

Hi Shashi,
I have configured D-Link 2750U using your steps. But I cant use more than 2 devices. Can u please suggest a way so that I can login once and all other devices can use wifi as well as via ethernet.
Thanks,
Vimal

Click to expand...

I assume u are using tikona, hence ur unable to connect (them online) more than 2 devices. Its tikona's limit that they do not allow more than 2 devices simultaneously logging in.

skyabcred said:

my router stopped responding after trying to complete step 5. I had to then hard reset it. please help. I have a rj45 lan cable coming from my wireless receiver which I need to connect to D-Link 2750u to make my environment wireless.

Click to expand...

You might have connected to a different port other than LAN1 while you were configuring these steps. Try connecting to your admin login page with LAN cable in LAN1 port and you should be able to continue further and connect fine. Many people have followed these steps and successfully connected (see their posts below)

vvvimal said:

Hi Shashi,
I have configured D-Link 2750U using your steps. But I cant use more than 2 devices. Can u please suggest a way so that I can login once and all other devices can use wifi as well as via ethernet.
Thanks,
Vimal

Click to expand...

I searched for a post which mentions about a hack to use same MAC on different devices.

Hi Shashi,
I was able to connect to internet via WIFI as well as LAN(i.e. 2 connections) for 1 day. The next day onwards I am unable to open the tikona login page even if I am connected to WIFI. My internet connection via LAN(single PC) is working fine. I tried it on 2 phones but still I am not able to get the tikona login page. What should I do to get it working?