Using the Dlink 2750u as a true Ethernet WAN router

Check D-Link DSL-2750U Deals on: Flipkart | Amazon | Snapdeal | Infibeam

I'd actually already posted on how to use the D-Link 2750u as a full fledged Ethernet WAN router, but it was a few pages deep in a Tikona thread and some users were getting the actual method mixed up with workarounds posted earlier in that thread.

The 2750u is actually capable of both adsl and Ethernet WAN routing. However the Indian firmware only enables the adsl WAN. So one needs to use the Middle East (ME) or Russian (NRU) firmware to enable the Ethernet WAN function (with the ME/Russian firmware one can use adsl, ethernet or 3g WAN). Please check the label under your router to identify the specific hardware version and apply the firmware that corresponds to it. Warning: You may brick your router if you apply the wrong firmware. Presently ME firmware is available for C1 and U1 versions. NRU firmware is available for C1. The NRU firmware has the mac cloning feature so you need not ask your provider to reset the mac lock (if mac lock is present). Here are the links

ME C1 v1.3

DSL-2750U_ME_1.30_B038_K8B_0K_ME3G-00-test-3388-20111231.img - Google Drive

ME C1 latest

bcm96328GW_K8B_0K_MEGE_fs_kernel_return_20131010.img - Google Drive

In the latest firmware, I'm having a problem getting my 3g dongle to work, which is why I've posted both versions. Once the firmware has been changed to the ME type, one can easily switch between versions (of the same hw type) using the software update page and one can choose which version works best for them.

ME U1
http://www.dlinkmea.com/partner/media/product_item_downloadables/1351-DSL2750U-U1_FW1.11.rar (Use 7zip/Winrar etc to extract firmware)

NRU C1
ftp://ftp.dlink.ru/pub/ADSL/DSL-2750U/Firmware/1.0.14/DSL_2750_v1.0.14_cfe_fs_kernel

Applying the firmware

The firmware may not be accepted in the normal firmware update mode. Then you'll need to update it in the dlink crash recovery mode using a LAN cable (not wirelessly). Assign a static address on the PC for the ethernet interface in the 192.168.1.x series for eg 192.168.1.5

Switch router off, press the reset button ie insert ballpoint pen in reset hole under the router, keep holding the reset button and turn on the router. Keep holding the reset button for about 12 seconds after you power on the router. Now you'll see that the power led has turned red signifying that the router is in crash recovery mode. When you enter the address 192.168.1.1 on your PC browser, you find the upgrade firmware page. Just browse to the downloaded firmware file and flash!

After the new firmware has been flashed, your internet connection will not start working automatically, you will also need to set up the router correctly. Please do not apply any workarounds mentioned in other threads such as interface grouping, disabling DHCP etc

Instructions for setting up the C1 hw version router with ME firmware

Step 1: Log into your router and under Advanced setup->Layer2 interface->ETH interface create an Ethernet interface with connection mode as default. Then go to Advanced setup->WAN Service and add service for eth0/LAN4.

Step2: If you have an internet connection with pppoe dialing such as pacenet, Honesty etc, in the next page, choose pppoe and put in username, password and service name in the next page. Also choose to enable NAT. In the next page move eth0 from available to selected gateway interface (if it's not already in selected) and remove ppp0 (if present) from selected, in the next page do the same for DNS and finally apply/save. Do thisonly if you have both eth0 and ppp0 appearing in the setup, else let ppp0 remain in selected.

Step2 (alt): If you have a connection such as Tikona, Reliance metro, cable internet (without pppoe dialer) etc, in the next page choose ip over ethernet, in the next page let the setting remain at Obtain an IP address automatically, in the next page check option to enable NAT, in the next page move eth0 from available to selected gateway interface (if it's not already in selected) and remove ppp0 (if present) from selected, in the next page do the same for DNS and finally apply/save. Do this only if you have both eth0 and ppp0 appearing in the setup, else let ppp0 remain in selected.

Step3: Then in advanced setup - 3g connection select primary uplink as ethernet.

Now connect your internet cable to the LAN port 4 of the router and you should be able to connect through any device connected through wifi or any of the other LAN ports. If you have a connection with a browser login such as Reliance metro or Tikona, the login page will show up only on the first device that you connect in each session. After you have logged in on any device, all other devices will have internet connectivity without going through the login page.

Instructions for setting up the U1 hw version router

In Internet setup, set WAN access type to Ethernet and in protocol, choose dynamic ip for connection such as Tikona, Reliance metro, cable broadband (without pppoe dialer) etc and choose pppoe if you have a pppoe dialer based connection such as pacenet, honesty net solutions etc. When setting up the internet connection, vlan id must not be given any value other than 0.

Instructions for setting up the C1 hw version router with NRU firmware (Port 1 is WAN port)

After you flash the interface will appear in Russian. Click on the rightmost dropdown at the top of the page and choose English to change the interface language.

Click on Advanced Settings at the bottom
Click on Interface Grouping in the Advanced section. Right click on the LAN icon on the right and click on setup speed and stream. There's some quirk in the interface and it's a little tricky getting this click right. Set duplex and speed to auto and save. Again hover mouse over LAN graphic and click on Make WAN. With the default option of 'Single service...' click save. Go back to the advanced settings screen. In the Net section click on WAN and add a connection. Choose connection type accordingly and choose LAN as the interface. Change MAC if required (if provider uses mac lock), (mac cloning doesn't seem to work) put in other details as needed (make sure NAT stays enabled) and click save. Internet cable goes into port 1 and not port 4 as in the case of the ME firmware
If your provider uses a mac id lock, plug in the internet cable in port 4 (port 1 for Russian fw) after completing the setup and ask him to register the new mac in his database.
Any users seeking help on this thread, please provide all relevant details (provider, type of connection) and screenshots (info and setup). Also please make absolutely sure that it's not a mac lock issue, as many users are needlessly seeking help on the forum without having got a proper mac reset from their provider.
 
Last edited by a moderator:
Messages
77
Location
NA
I have same modem (2750u, HW: V1 and FW:IN_1.02). I already flashed it with ME1.03 firmware
I'm using pppoe dialing (pacenet) connection. My connection provider says to put "qualityinternet" as service name in pppoe setting as shown below
Capture.png

But I'm unable to edit service name in setting page of my modem like following
Capture.png


So I cannot use it. Can anyone please help with it?
Thanks in advance.

Unfortunately service name cannot be changed, without proper service name my internet connection is not working.

Is there any other firmware that allows editing the service name? If anyone gets a solution let us know.
 
Messages
3
Location
NA
ISP
MTNL
Hi. I had flashed the firmware to ME1 and was using it for MTNL FTTH for about a year. Now I have had to move the ISP to GTTPL/Lunatech and need help on it.

While the diagnostics provided in the modem is passing the test for authentication to ISP and connectivity is showing up, ( even the DNS is assigned from ISP) the LAN and Wireless is not connecting to internet. There is no Mac Lock - which was confirmed by the ISP.

seems like I am missing out some step on the connectivity from the WAN to LAN/ Wireless ? Can someone please guide me?

Regards

EDIT 6th Sept

Found the problem. Put a keep alive to 1800 secs, 20 retries max ( max and random value). and also the LAN WAN bridge on the same screen where the credentials are provided. ( not sure which one did the trick because independently both were not working ...but this combo worked!!!)
 
Last edited:

joyceanblue

Newbie
Messages
107
Location
New Delhi
ISP
MTNL
Does anyone know where the remote management option is in the router's settings? the setting page looks totally different to what it shows in the manual and there is Tool Tab.
dlink.jpg
 
Last edited by a moderator:
Messages
1
Location
NA
Hi friends, i bought a new printer wired. Currently the modem am using is D-Link dir816. In that modem im not having usb port.. In having another modem not connected to internet 2750u which has usb port. Is there anyway i can use the second router 2750u and connect the printer to dir816 and make the printer wireless. Please help me to resolve the issue. Currently am having bsnl connection.
 
Messages
1
Location
NA
Manoj
very well written, thank you.
I don't have neither C1 or U1 hardware but have V2 h/w.
For V2 Hardware I installed ME_1.16 but WAN did not work by PPPoE.
Any help will be highly appreciated.

Is indian firmware available to download to revert back?
 


Messages
1
Location
NA
ISP
BSNL
Hello,
I am using D-Link 2750U and wanted to use it as a wifi router with BSNL FTTH. The H/W Ver is A1 and F/W Ver is IN_1.01.
WAN is working through this modem using cables, but unable to set up wifi though tried multiple options as shared by users.
Any help in this regard will be highly appreciated.
Thanks!
 

popcorn

Senior Member
Messages
3,293
Location
Mumbai
ISP
One Broadband(15mbps) & MTNL 600 Combo(12mbps)
You need to do a routing manually as I faintly remember. I have this setup in my home and I had struggled at this exact point and had to do this manual routing setting somewhere...
Let me know if you need my help.
 
Messages
2
Location
NA
ISP
dna