Hi all,I'm using MTNL, Mumbai ADSL connection. I recently purchased the D-Link DSL-2750U router and thought setup would be easy. :banghead: No such luck. I also have a ZyXEL router which is working fine with the same MTNL connection. (I'm currently using ZyXel to access this forum)I saw a website which had a guide for 2730U setup for MTNL. When i followed the steps I'm unable to get internet on this D-Link 2750U router. I always end up with a RED light on the internet symbol on the router. Can someone PLEASE guide me with steps to get internet active on this router? I would really appreciate this. Thanks a lot.
-
Amazon Deals - ToS - Warp
Need help configure D-Link DSL-2750U to work with MTNL, Mumbai
- Thread starter koolpal
- Start date
- Replies 26
- Views 64,546
K
kreacher10
If I am not mistaken this is a modem cum wifi router, so you will have to connect the tel wire to this unit . Have you checked ftp://support.dlink.co.in/broadband/DSL-2750U/manual/DSL-2750U_C1_Manual_IN_1.00.pdf. Just remember that VPI = 0 & VCI = 32 for MTNL
If I am not mistaken this is a modem cum wifi router, so you will have to connect the tel wire to this unit . Have you checked ftp://support.dlink.co.in/broadband/DSL-2750U/manual/DSL-2750U_C1_Manual_IN_1.00.pdf. Just remember that VPI = 0 & VCI = 32 for MTNL
Thanks kreacher10, I have done that plus input phone number & CA number, etc..
No luck.
Can anyone using this router with MTNL Mumbai guide me with each & every field level setting?
Even screenshots would do.
Thanks a ton.
Thanks kreacher10, I have done that plus input phone number & CA number, etc..
No luck.
Can anyone using this router with MTNL Mumbai guide me with each & every field level setting?
Even screenshots would do.
Thanks a ton.
x720
Incoherent Poster
Post screenshots of the setup page and I'll post the values.
K
kreacher10
I would suggest you reset the unit to factory settings then try again, its possible that some changes made in a previous attempt is causing a problem now 🙂
x720
Incoherent Poster
Well, you could begin by posting the values you've entered into the modem.
Hi all,
I'm using MTNL, Mumbai ADSL connection.
I recently purchased the D-Link DSL-2750U router and thought setup would be easy. :banghead: No such luck.
I also have a ZyXEL router which is working fine with the same MTNL connection. (I'm currently using ZyXel to access this forum)
I saw a website which had a guide for 2730U setup for MTNL. When i followed the steps I'm unable to get internet on this D-Link 2750U router.
I always end up with a RED light on the internet symbol on the router.
Can someone PLEASE guide me with steps to get internet active on this router?
I would really appreciate this.
Thanks a lot.
You should use the installation cd & follow the instructions
I'm using MTNL, Mumbai ADSL connection.
I recently purchased the D-Link DSL-2750U router and thought setup would be easy. :banghead: No such luck.
I also have a ZyXEL router which is working fine with the same MTNL connection. (I'm currently using ZyXel to access this forum)
I saw a website which had a guide for 2730U setup for MTNL. When i followed the steps I'm unable to get internet on this D-Link 2750U router.
I always end up with a RED light on the internet symbol on the router.
Can someone PLEASE guide me with steps to get internet active on this router?
I would really appreciate this.
Thanks a lot.
You should use the installation cd & follow the instructions
Follow these steps ........
1. Open the configuration website by typing ‘http://192.168.1.1/’ in the address bar of your web browser (Internet Explorer or Firefox or Chrome) and press the 'Enter' key.
2. Enter username and password which is “admin” for both by default.
3. Click on "Advance setup" from the menu on the left hand side.
4. Click on the 'Add' button.
5. Enter values for VPI (BSNL and MTNL) = “0” and for VCI (BSNL) = “35" and (MTNL) = “32".
6. The other fields should be:
Select the DSL Latency: Path 0
Select the DSL Link Type: EoA
Select Connection mode: Default
Encapsulation Mode: LLC/SNAP –BRIDGING
Service category : UBR Without PCR
Select the IP QoS Scheduler Algorithm to Strict Priority
7. After entering the above data, click on 'Apply/Save' button.
8. Click on 'WAN Service' button on the menu on the left hand side.
9. Click on 'Edit' button.
10. Enter your PPP username and password (For MTNL, Username is your DSL line phone number and Password is your CA number. These are mentioned on your bill). "Authentication mode" should be set to "AUTO". Leave all other options on this page unchecked.
11. Click on 'Next' button and then click on 'Apply/Save' button.
Your 2750U should work now!
1. Open the configuration website by typing ‘http://192.168.1.1/’ in the address bar of your web browser (Internet Explorer or Firefox or Chrome) and press the 'Enter' key.
2. Enter username and password which is “admin” for both by default.
3. Click on "Advance setup" from the menu on the left hand side.
4. Click on the 'Add' button.
5. Enter values for VPI (BSNL and MTNL) = “0” and for VCI (BSNL) = “35" and (MTNL) = “32".
6. The other fields should be:
Select the DSL Latency: Path 0
Select the DSL Link Type: EoA
Select Connection mode: Default
Encapsulation Mode: LLC/SNAP –BRIDGING
Service category : UBR Without PCR
Select the IP QoS Scheduler Algorithm to Strict Priority
7. After entering the above data, click on 'Apply/Save' button.
8. Click on 'WAN Service' button on the menu on the left hand side.
9. Click on 'Edit' button.
10. Enter your PPP username and password (For MTNL, Username is your DSL line phone number and Password is your CA number. These are mentioned on your bill). "Authentication mode" should be set to "AUTO". Leave all other options on this page unchecked.
11. Click on 'Next' button and then click on 'Apply/Save' button.
Your 2750U should work now!
koolpal help me out ,I am facing the same problems as u did.The Red light still stays on after all the steps i followed from this post please reply ASAP !!koolpal said:
