BSNL Broadband: Limited or no connectivity...

  • Thread starter Thread starter rulingrulz
  • Start date Start date
  • Replies Replies 9
  • Views Views 10,613
R

rulingrulz

Newbie
Messages
2
Location
NA
ISP
BSNL
hey guys after reseting my siemens c2110 modem for about 10 times my modem is showing a problem and the problem is that in its LAN connectivity it shows an alert with "limited or no connectivity" but net is able to be connected with no decrement in the speed but my router setting page is not opening.....so wat to do plzzz help..........
 
........but net is able to be connected with no decrement in the speed but my router setting page is not opening.....
1.
If connection is automatic confirm. Dialer not used.
2.
Reset once More!
modem will go to factory defaults.
In computer
Start/Network LAN properties
TCP/IP properties
enter'
192.168.1.10
255.255.255.0
192.168.1.1
dns
208.67.220.220
208.67.222.222
Save apply

Open IE browser
Type 192.168.1.1 admin admin
Do not select "Bridged" in WAN page.
select ppp/PPPoE
enter userID (without @bsnl.in preferably ) PW erc
Save reboot
wait for two minutes.

C2110 (Type-A) ADSL MODEM MULTIUSER CONFIGURATION

REF:
 
just assign ip in tcp/ip setup...also disable ur firewall which cause limited connectivity...
:thumb:

---------- Post added at 11:28 AM ---------- Previous post was at 11:27 AM ----------

also use this setting
ip:192.168.1.1
gateway:it wud be generated

dns primary:192.168.1.1 this wud help....:ashamed:
 
I m also having same problem,Plz anyone help.My internet speed goes down due to this.

1. Please mention your modem - model and make

2. Use the following values in TCP/IP properties of your connection.

IP : 192.168.1.25

Subnet mask : 255.255.255.0

Default gateway : 192.168.1.1

3. If confident, reset the modem to factory default and reconfigure it
 
i did setting TCP/IP to __________________IP : 192.168.1.25Subnet mask : 255.255.255.0Default gateway : 192.168.1.1____________________Now it Shows my lan to be connected BUT its giving me half the speed with this.Without this settings,lan says limited or no connectivity,my internet connects,speedtest.net download speed: 1.37mbps.With these settings,lan says connected,my internet connects,speedtest.net download speed: 0.47mbps.What should i do so that lan shows "connected" with automatic ip in tcp/ip settings?how can i configure modem to act as DHCP server so i will be able to get the IP when the client requests?thanks for your reply.
 

1. Mention, modem - model and make.

2. Log in to the modem using 192.168.1.1 in browser and ID, password as admin. You will find an option to enable DHCP.
 
Board ID: 96338L-2M-8MSoftware Version: 3.08.BSNL_02.01.02_tr64.Bootloader (CFE) Version: 1.0.37-8.7Firmware Version: UT300R2U.0011.01Hardware Version: UT300R2U 2.2Model Name: UT300R2UThis information reflects the current status of your DSL connection.Line Rate - Upstream (Kbps): Line Rate - Downstream (Kbps): LAN IP Address: 192.168.1.1Default Gateway: Primary DNS Server: 192.168.1.1Secondary DNS Server: 192.168.1.1I cant find in 192.168.1.1,where to enable DHCP.
 
Board ID: 96338L-2M-8M
Software Version: 3.08.BSNL_02.01.02_tr64.
Bootloader (CFE) Version: 1.0.37-8.7
Firmware Version: UT300R2U.0011.01
Hardware Version: UT300R2U 2.2
Model Name: UT300R2U

This information reflects the current status of your DSL connection.

Line Rate - Upstream (Kbps):
Line Rate - Downstream (Kbps):
LAN IP Address: 192.168.1.1
Default Gateway:
Primary DNS Server: 192.168.1.1
Secondary DNS Server: 192.168.1.1

I cant find in 192.168.1.1,where to enable DHCP.

USE PPPoE mode( USERID/PW stored/entered in WAN page )
SeeAdvanced options LAN
The little I know about Dataone Broadband Services offered by BSNL
 

Top